工業PH復合電極前段的保護瓶內有適量電極浸泡溶液，電極頭浸泡其中，以保持玻璃球泡和液接界的活化，測量時旋松瓶蓋，拔出電極，用去離子水洗凈即可使用。測量前，應注意將玻璃泡內氣泡甩去，否則將造成測量誤差，測量時應將電極在測試溶液中攪動后靜止放置，以加速響應。檢查接頭處是否干燥清潔，如有沾污，需要用*擦洗干凈吹干后使用。建議采用二點法校準電極，通常先用PH6.86緩沖液校定位，再用PH4.01或PH9.18緩沖液確定斜率。用后再將電極插進保護瓶并旋緊瓶蓋，經防止溶液滲出。電極應定時清洗若電極玻璃球泡與聚四氟乙烯環形液接界污染，可以用以下的方法進行清洗：*、表面活性劑；第二、鈣沉淀物或金屬氫氧化物可用10%的稀鹽酸清洗；第三、硫化物沉淀可用10%的稀鹽酸清洗；第四、蛋白質復合物可用10%的稀鹽酸和胃蛋白酶的混合物進行清洗。

發件人：LL002